# Kill switch from boot.

While Fenris is on, nothing from your device, or from the devices behind your router, leaves outside the tunnel. Not while it connects, not after a crash, not during an upgrade.

_Every device · On by default_ 

The tunnel can’t be reached The tunnel is up

Without a kill switch _Leaves directly, from your home address_

With Fenris _Held back until the tunnel is back_

With Fenris _Through the tunnel, from your server’s address_

**Fig. 1** On wired networks you list, traffic can go direct instead, after 30 seconds without your server. Never on open Wi-Fi.

## What happens

1. The block goes up before the network does. On a router or a PC it holds from early boot, before anything can send.
2. Only the tunnel to your server is let out. Everything else waits behind it.
3. If the tunnel can’t be reached, traffic waits, and the app says so. The tray reads Holding traffic.
4. Name lookups are forced into the tunnel. IPv6 goes through it when your server has IPv6, and is refused at once otherwise, so it never leaks.
5. A crash or an upgrade leaves the block in place. It comes down only when you turn Fenris off.

## What it costs

No tunnel, no internet, until it is back.

**While your server is away**

Traffic waits. Nothing loads until your server answers, a second server takes over, or you turn Fenris off.

**One address**

Websites see your server’s address for everything. Some banks and streaming services distrust addresses that belong to a hosting provider.

**Going direct**

A site you set to go direct leaves outside the tunnel. It gets no bonding, and the network it leaves by can see it.

**Sign-in pages**

A hotel’s sign-in page can’t load through the block. One device is let through to it, for up to 5 minutes.

## Turn it on

It is on from the start. These open it where you choose.

| To                                  | Command line                                   | Router UI and app                    |
| ----------------------------------- | ---------------------------------------------- | ------------------------------------ |
| Turn the kill switch off            | fenris settings \--kill-switch off             | Settings, When Fenris can’t connect  |
| Let chosen sites go direct          | fenris settings \--direct-domains bank.example | Settings, Direct, outside the tunnel |
| Let a device at home go direct      | fenris settings \--direct-devices 192.168.1.40 | Settings, Direct, outside the tunnel |
| Go direct while only one link works | fenris settings \--direct-when-alone on        | Settings, Direct, outside the tunnel |
| Turn the tunnel off for now         | fenris disconnect                              | Home, the switch                     |
| Check each step to your server      | fenris check                                   | Diagnostics                          |

### Where to find it

**Router UI** Home. Protected, and through which server.

The router’s own page, Home, with example data: connected, two of three links up, the speed over both as one, and each link with its share.

**The app** Home. On Android, the kill switch is the system’s own always-on VPN setting.

The Android app’s Home screen, with example data: protected, two links up, and each link’s share of the traffic.

**The tray** Connected, Connecting, Holding traffic or Off.

The tray on a PC, with example data: connected through one server over three links, and each link’s round trip and share.

**The product** Three of its own screens, with example data.

## What it keeps

Nothing. The kill switch is a rule on your device. It records nothing and sends nothing.

[Everything your server keeps](https://fenris.network/privacy#kept)

## Where it stops

**When Fenris is off**

Turn Fenris off and traffic leaves directly, as it did before. The app warns you when you do.

**Networks you trust**

On wired networks you list, traffic goes direct after 30 seconds without your server. Never on open Wi-Fi.

**Past your server**

It keeps traffic inside the tunnel. Past your server, traffic is as protected as the website makes it.

**On Android**

The kill switch there is Android’s always-on VPN setting, with “Block connections without VPN”. The app shows you where it is.

## Related
